Daugiau informacijos rasite {+}https://mt.lv/help-lt+LV. The device will now look for a CAPsMAN server (total 10 seconds). Den fullständiga texten till EU-försäkran om överensstämmelse finns på följande webbadress: This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. RouterBOARD cAP-2nD (ceiling Access Point) is our first 2.4GHz Dual-Chain ceiling AP. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and any part of your body. The below image shows the location of the Reset Jumper on older RouterBOARDs like RB133C: Note: Don't forget to remove the jumper after the configuration has been reset, or it will be reset every time you reboot. These limits are designed to provide reasonable protection against harmful interference in a residential installation.This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. But if you restore a backup from two hardware types that are very similar, you will be able to restore the file but with some strange results. By default, the device is configured as a wireless access point, with the first ethernet port (Eth1) configured as a DHCP client, and the second interface bridged together with the wireless interface. Откройте 192.168.88.1 в своем веб-браузере для конфигурации. Návod k použití: Připojte napájecí adaptér k zapnutí přístroje. Iftaħ 192.168.88.1 fil-web browser tiegħek, biex jiġi kkonfigurat. Products with the letters “EG” at the end of their serial number have their wireless frequency range limited to 2.400 – 2.4835 GHz, the TX power is limited to 20dBm (EIRP). El texto completo de la declaración UE de conformidad está disponible en la dirección Internet siguiente: Käesolevaga deklareerib Mikrotīkls SIA , et käesolev raadioseadme tüüp RouterBOARD vastab direktiivi 2014/53/EL nõuetele. Navodila: Priključite napajalnik za vklop naprave. Odprite 192.168.88.1 v spletnem brskalniku nastaviti izdelek. If you are unable to manage your MikroTik device, you can factory reset by pressing the reset button.
We suggest starting here to get yourself accustomed to the possibilities: https://mt.lv/help. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Åpne 192.168.88.1 i en nettleser for å konfigurere produktet. Operation of this equipment in the residential environment could cause radio interference. This equipment should be installed and operated with a minimum distance of 20 cm between the device and your body. The device will boot up and Wireless network will be available for connecting. Some devices might need opening of the enclosure, RB750/RB951/RB751 have the jumper hole under one of the rubber feet of the enclosure. Manuale di istruzioni: Collegare l'adattatore di alimentazione per accendere l'unità. Lisää tietoa {+}https://mt.lv/help-fi+FR. Rohkem teavet {+}https://mt.lv/help-et+FI. You might need the assistance of another person to push the button and also plug the power supply at the same time, 2) press and hold the button right after applying power, Note: hold the button until LED will start flashing. Manufacturer: Mikrotikls SIA, Brivibas gatve 214i Riga, Latvia, LV1039. Without any restriction to use in all EU Member States, * It is the customer's responsibility to follow local country regulations, including operation within legal frequency channels, output power, cabling requirements, and Dynamic Frequency Selection (DFS) requirements. Package includes the following accessories that come with the device: For more information about this product, specification and pictures please visit our web page: https://mikrotik.com/product/cap_ac.